+49 201 749189-21
Monday to Friday 8 am - 5 pm (CET)

+49 201 749189-21
Monday to Friday 8 am - 5 pm (CET)

Sensor for point level detection G 1/2 male

AF006Sensor for point level detection G 1/2 male

G 1/2 M

Installation at rear

Programmable

Go to customer reviews(4)

NET PRICE (plus VAT)

109.41 €

Offline: 115.78 €

GROSS PRICE (incl. VAT)

130.19 €

Offline: 137.77 €

Incl. 5.50 % online discount

30 in stock!

Technical data Downloads

Overview

For optimum level measuring with water, water-based media, oils, oil-based media, coolants and powdery media
Deposits and foam are largely suppressed; splashes, air bubbles and wave movements can be largely suppressed by adjustment
2x programmable normally open/ normally closed
Temperature measurement at the probe tip; for media temperature -25...100 °C
Parameterisation only via IO-Link

Industry 4.0 & IIoT

Discover a universe of new possibilities with smart solutions from autosen

Discover now

Description

The AF006 binary level sensor with process connection and the high protection ratings of IP68 / IP69K is suitable for limit detection of water and water-based media, oils, oil-based media, coolants and powder-type media.

It is pre-set for water-based media. The factory setting suffices in many cases, but the sensitivity and other functions can also be adjusted to suit the application in question. For instance, a switching delay can be set to mask out the effects of spray, wave motion and air bubbles. Please contact us if you have any questions on parametrization. The AF006’s strong point can be seen in its special sensor principle that suppresses the effects of adhesion or foam formation.

It’s two programmable switching outputs (normally open / normally closed) can be parametrized via the digital IO-Link communication interface. With the aid of a welding adapter the sensor can be rear-mounted into a pipe of variable length. This allows for the definition of different actuation points. You will find a mounting example in our know-how section.

In addition to limit detection, the process temperature can be measured at the probe tip. It should be borne in mind that the temperature measurement can only be carried out via the IO-Link interface with acyclical data querying if the probe tip is sufficiently covered by the medium during the measurement.

You will find suitable accessories and a detailed technical data sheet on the AF006 further down.

If you have questions regarding the IO-Link parameterization or want to use the parameterization service of autosen, please do not hesitate to contact us. Or start directly with the IO-Link starter kit ADS01.

Weiterlesen Hide

Technical data AF006

General information

Range of application Water-based cooling lubricants, oils, water / media similar to water
Cannot be used for: See the operating instructions

Outputs / inputs

Switching output 2 x normally closed / normally open programmable
IO-Link Yes

Electrical data

Operating voltage 18 ... 30 V DC
Voltage type Direct voltage (DC)
Electrical design PNP
NPN*
*IO-Link parameterisation
Current carrying capacity max. 50 mA
Voltage drop max. 2.5 V
Current consumption max. 35 mA
Protection class III
Short-circuit protection Yes
Overload-proof Yes
Reverse polarity protection Yes

Mechanical data

Materials in contact with the medium V4A (1.4404)
FKM
PEEK
Material of housing PEI
V4A (1.4404)
FKM
PEEK
Electrical connection M12
4-pin
Contacts gold-plated
Process connection External thread
G 1/2
Probe length L 9.6 mm Installation at rear

Ambient conditions

Ambient temperature min. -25 °C
Ambient temperature max. 85 °C
Maximum container pressure -1 ... 40 bar
Medium temperature -25 ... 100 °C °C
Protection rating IP68
IP69k

Additional information

MTTF 534 years
Function display Yellow
Green
2 x LED
Accessories included with delivery No accessories included
EMC test DIN EN 61000-6-2
DIN EN 61000-6-4
DIN EN 61000-6-3
Shock resistance test DIN EN 60068-2-27
Vibration resistance test DIN EN 60068-2-6
Approval CE
cULus